Search found 138 matches

by kolederacer
Wed Jul 27, 2016 12:05 pm
Forum: FZR1000
Topic: 88 FZR1000 Stage 3
Replies: 14
Views: 4200

Re: 88 FZR1000 Stage 3

I think you should probably look into this after what everyone else is saying also. After the changes to mine the 140 jet turned the swing arm black in a couple of days when i still had my low exhaust.
You can actually see it in my avatar.
by kolederacer
Tue Jul 26, 2016 10:09 pm
Forum: FZR1000
Topic: 88 FZR1000 Stage 3
Replies: 14
Views: 4200

Re: 88 FZR1000 Stage 3

Also it could be an ignition issue.
by kolederacer
Tue Jul 26, 2016 10:08 pm
Forum: FZR1000
Topic: 88 FZR1000 Stage 3
Replies: 14
Views: 4200

Re: 88 FZR1000 Stage 3

Are you running a non stock cam? I ran into an interesting situation on mine where after mods including cam and big bore and porting it wanted leaner jets than before. I personally believe it was because the change in velocity in the carbs which was much high so even though there was a smaller jet t...
by kolederacer
Sun Jul 24, 2016 6:27 pm
Forum: FZR1000
Topic: Are all fzr1000 ignition coils interchangeable?
Replies: 2
Views: 1070

Re: Are all fzr1000 ignition coils interchangeable?

I believe they are the same ohms.
by kolederacer
Sat Jul 23, 2016 2:44 am
Forum: FZR1000
Topic: Genesis revival
Replies: 26
Views: 4591

Re: Genesis revival

I have been saving for a lathe and mill. Would help out a lot. How much would you change for a set for the fzr? I may be interested if it's less than bearings.
by kolederacer
Fri Jul 22, 2016 1:00 pm
Forum: FZR1000
Topic: Genesis revival
Replies: 26
Views: 4591

Re: Genesis revival

I like what you did with the washers to seal the bearings. Do you put any seal under them to keep sand and powder out?
by kolederacer
Thu Jul 21, 2016 2:12 pm
Forum: FZR1000
Topic: Genesis revival
Replies: 26
Views: 4591

Re: Genesis revival

Nice work on the exhaust. I need to get around to building mine. Probably going with an R-77 can.
by kolederacer
Thu Jul 21, 2016 2:11 pm
Forum: FZR1000
Topic: 1988 FZR 1000 Build
Replies: 42
Views: 14074

Re: 1988 FZR 1000 Build

Apparently they are ok for general road use as they don't really become active until you get the revs up a bit and they tighten up, not tried it yet though. But if the set up you have works then happy days. I didn't know the YZF basket was an upgrade. One of the reasons i joined this forum :thumbsu...
by kolederacer
Mon Jul 18, 2016 4:30 pm
Forum: FZR1000
Topic: Genesis revival
Replies: 26
Views: 4591

Re: Genesis revival

looking great!
by kolederacer
Mon Jul 18, 2016 4:28 pm
Forum: FZR1000
Topic: 1988 FZR 1000 Build
Replies: 42
Views: 14074

Re: 1988 FZR 1000 Build

I have never seen one of the lock up clutches actually.
But i dont think it would work out too well for road course.
I have a YZF750 basket on an fzr1000 main gear that i have not had any issues with...
by kolederacer
Mon Jul 18, 2016 12:30 pm
Forum: FZR1000
Topic: 1988 FZR 1000 Build
Replies: 42
Views: 14074

Re: 1988 FZR 1000 Build

So its been a while and the FZR got put on the back burner but i am finally getting going on it again. Just picked up a set of a real full set of Ti valves for the bike as well as race springs and TI retainers. http://i270.photobucket.com/albums/jj92/kolederacer/20160716_115726_zpshqpt9hjk.jpg
by kolederacer
Mon Jul 18, 2016 12:05 pm
Forum: FZR1000
Topic: Genesis revival
Replies: 26
Views: 4591

Re: Genesis revival

Also if you have something you really cant fix i pretty much have a second parts bike and most of it is pretty good.
by kolederacer
Sun Jul 17, 2016 10:36 am
Forum: FZR1000
Topic: Genesis revival
Replies: 26
Views: 4591

Re: Genesis revival

Very impressive metal work! i would not have even bothered with that bike it was rough.
by kolederacer
Wed Jul 13, 2016 12:01 pm
Forum: FZR1000
Topic: FZR seat unit change
Replies: 8
Views: 1974

Re: FZR seat unit change

I used an RC complete tail and rebuilt part of it to bolt to the fzr frame. Check out my build thread.
by kolederacer
Tue Jun 28, 2016 3:50 pm
Forum: FZR1000
Topic: FZR 1000 Race Engine Build
Replies: 22
Views: 9565

Re: FZR 1000 Race Engine Build

Hi guys, Corey doesn't usually jump start, if you look in the video the bike beside him jerks forward and that triggers his start. We are looking into adjustable ignition systems that will allow a different rev limiter. Now onto the main course...here is the bike (aka flamethrower) on the dyno, rig...

Go to advanced search